|
72(t) Calculator Glossary of Terms
Definitions
- Reasonable
interest rate
- This is any rate less than or equal to 120% of the Federal Mid-Term
rate for either of the two months immediately preceding the month
in which the distribution begins. Click
here for more information.. For January 2008, 120% of the Federal
Mid-Term rate is 4.31%.
It is important to note that the associated law that created 72(t)
distributions did not define what was to be considered a reasonable
interest rate. As such, the guidance from the IRS generally flows
from the concept that they will not allow people to circumvent the
requirement of substantially equal periodic payments (SEPP) throughout
your lifetime by using an unreasonably high interest rate.
72(t) withdrawals setup prior to January, 2003, had some flexibility
in the choice of the reasonable rate to use. However, in 2002, the
IRS issued new rules stating that only rates less than or equal
to 120% of the Federal Mid-Term rate would be considered reasonable.
You are now required to use a rate that is less than or equal to
120% of the Federal Mid-Term rate for either of the two months immediately
prior to the start of your distribution plan.
- Substantially
Equal Periodic Payments (SEPP)
- The rules for 72(t)/(q) distributions require you to receive Substantially
Equal Periodic Payments (SEPP) based on your life expectancy to avoid
a 10% premature distribution penalty on any amounts you withdraw.
Payments must last for five years (the five-year period does not end
until the fifth anniversary of the first distribution received) or
until you are 59 1/2, whichever is longer. Further, the SEPP amount
must be calculated using one of the IRS approved methods which include:
- Required minimum distribution method: This is the simplest
method for calculating your SEPP, but it also typically produces
the lowest payment. It simply takes your current balance and divides
it by your single life expectancy or joint life expectancy. Your
payment is then recalculated each year with your account balance
as of December 31st of the preceding year and your current life
expectancy. This is the only method that allows for a payment
that will change as your account value changes. Even though this
may provide the lowest payment, it may be the best distribution
method if you expect wide fluctuations in the value of your account.
- Fixed amortization method: With this method, the amount
to be distributed annually is determined by amortizing your account
balance over your single life expectancy, the uniform life expectancy
table or joint life expectancy with your oldest named beneficiary.
- Fixed annuitization method: This method uses an annuity
factor to calculate your SEPP. This is one of the most complex
methods. The IRS explains it as taking the taxpayer's account
balance divided by an annuity factor equal to the present value
of an annuity of $1 per month beginning at the taxpayer's age
attained in the first distribution year and continuing for the
life of the taxpayer. For example, if the annuity factor for a
$1 per year annuity for an individual who is 50 years old is 19.087
(assuming an interest rate of 3.8% percent), an individual with
a $100,000 account balance would receive an annual distribution
of $5,239 ($100,000/19.087 = $5,239). This calculator uses the
mortality table published in IRS Revenue Ruling 2002-62, which
is a non-sex based mortality table. Please note that your annuitized
SEPP is based on your life expectancy only, and is not based on
the age of your beneficiary.
In addition, on July 3rd, 2002, the IRS ruled that you could change
your distribution type one time without penalty from the Annuitized
or Amortized methods to the Required Minimum Distribution method.
This would allow account holders the option to move from a fixed
payment type to a payment that fluctuates annually with the value
of their account. The primary reason for this exception is to allow
individuals who have suffered large losses, the option to reduce
their distribution to prevent their retirement account from being
prematurely depleted. For more information on this important exception
please see Revenue Ruling 2002-62 on www.treasury.gov.
If payments are changed for any reason other than death or disability
before the required distribution period ends, the distributions
may be subject to a retroactive application of the Premature Distribution
penalty. It is 10% (plus interest) for all years beginning the year
such payments commenced and ending the year of the modification.
It is important to remember that while 72(t) distributions are not
subject to the 10% penalty for early withdrawal, all applicable
taxes on the distributions must still be paid. Further, taking any
early distributions from a retirement account reduces the amount
of money available later during your retirement. Please contact
a qualified professional for more information.
- Account
balance
- The account balance used to determine the payment must be determined
in a reasonable manner. For example, with a first distribution taken
on July 15, 2003, it would be reasonable to determine the account
balance based on the value of the IRA from December 31, 2002 to July
15, 2003. For subsequent years, the same valuation date should be
used.
- Your
age
- This is your current age. Use the age you will turn on your birthday
for the year you are receiving the distribution.
- Beneficiary age
- This is your beneficiary's age. Use the age your beneficiary will
turn on their birthday for the year you are receiving the distribution.
This entry is ignored if you do not use your Joint Life Expectancy
to calculate your SEPP.
- Choose
life expectancy tables
- There are three different life expectancy tables that the IRS allows
you to use when calculating your SEPP with the "Fixed Amortization"
or the "Required Minimum Distribution" methods. It is important to
note that once you have chosen a distribution method and life expectancy
table, you cannot change either throughout the course of your distributions.
(Except for a one-time change from the Annuitized or Amortized methods
to the Life Expectancy method, see SEPP definition for more details).
The three life expectancy options are:
| Table |
Description |
Uniform Lifetime |
This is a non-sex based table developed
by the IRS to simplify minimum distribution requirements.
The uniform lifetime table estimates joint survivorship, but
does not use your beneficiary's age to determine the resulting
life expectancy. This table can be used by all account owners
regardless of marital status or selected beneficiary. |
| |
|
Single Life Expectancy |
This is a non-sex based life expectancy
table. This table does not use your beneficiary's age to calculate
your life expectancy. This table can be used by all account
owners regardless of marital status or selected beneficiary.
Choosing single life expectancy will produce the highest distribution
of the three available life expectancy tables. |
| |
|
Joint Life Expectancy |
This is also a non-sex based life expectancy
table for determining joint survivorship using your oldest
named beneficiary. |
|
|